Odometer Correction with the Diagprog 3 programmer

Easy and Safe Mileage Correction

Contact DiagProg CONTAKT  


I,m in problem,I need help. Accord 2008

I,m in problem,I need help. Accord 2008 Odometer Correction with the Diagprog III programmer:
Easy and Safe Digital Mileage Correction

I,m in problem,I need help. Accord 2008

 
Post new topic   Reply to topic    Odometer Correction Forum for Digital Mileage Correction -> Mileage Correction Honda
 
Author Message
ahmadiga
Junior member


Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
Posted: Sat Feb 23, 2008 1:10 pm    Post subject: I,m in problem,I need help. Accord 2008 Reply with quote
hello
Please i have a problem i need technical asistance.someone gave me accord 2008 dash to correct, before doing anything i post a question in this forum but no one seem to have done accord 2008, then i decided to open the cluster and do it and i read the eeprom but it was giving me wrong numbers.then i decided to return it back but when i return it back it refuse to work the odometer is blank,the fuel gauge,tachometer,speedometer and temp gauge stop working. Please i need your assistance i suspect the processor and i don't know where to find it,please if you know the cause of this problem help me out .i have 15 years electronic engineering experience,if you can help me with the parts i will pay you and i believe i can fix it because in my country there's no cluster spareparts. this is the number of the processor 6432638M58FV and the odometer is in KM. Please help me out.
Regards
Ahmadiga
Back to top
Edmond
Junior member


Joined: 06 May 2006
Posts: 17
Posted: Sat Feb 23, 2008 4:11 pm    Post subject: : I,m in problem,I need help. Accord 2008 Reply with quote
Did you save the dump when you read the eeprom?
Did you still try to programme it when even it show wrong numbers?
Did you check what type of chip you reading?
Did you de-solder off the board to read the chip?
Back to top
ahmadiga
Junior member


Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
Posted: Sat Feb 23, 2008 6:30 pm    Post subject: Accord 2008 Reply with quote
Hi
I did not save the dump,i did not programme the chip, i only read the chip without knowing the real number of the chip i select diferent honda models with my tacho dash prog. and no one that match with the original numbers. I did not remove the pointer from the dash because i'm afraid i only use a long needle attach to my ohmmeter and insert it between the board and the front plastic of the cluster to know the pins solder connections,and i got it. But i did not trace the crystal connection, And about soldering i did it well and i did not remove the chip.
Regards.
Ahmadiga
Back to top
Edmond
Junior member


Joined: 06 May 2006
Posts: 17
Posted: Sat Feb 23, 2008 10:15 pm    Post subject: : I,m in problem,I need help. Accord 2008 Reply with quote
I do not like to elaborate your impulses. The most concern
is the #5 & #8 connection. If it's connected in the wrong
spot or reverse connection, anything unpleasand could
happen.
Back to top
ahmadiga
Junior member


Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
Posted: Sat Feb 23, 2008 11:17 pm    Post subject: Accord 2008 Solution Reply with quote
Hi
The connection of pin 5 is ground and the connection of pin 8 is +5v everything is connected normal, if you have any idea of what may cause
that problem i will be glad to hear from you.
Wishyou Nice Weekend.
Ahmadiga
Back to top
hcip
Senior Member


Joined: 03 Mar 2006
Posts: 269
Location: Brgy. Commonwealth, Quezon City Philippines
Posted: Sun Feb 24, 2008 7:23 am    Post subject: Re: Accord 2008 Solution Reply with quote
ahmadiga wrote:
Hi
The connection of pin 5 is ground and the connection of pin 8 is +5v everything is connected normal, if you have any idea of what may cause
that problem i will be glad to hear from you.
Wishyou Nice Weekend.
Ahmadiga


Hello

If you have interchange the connections of data out pin & data in pin,
This will cause to erase the chip, even you are in reading mode

regards
_________________
Back to top
ahmadiga
Junior member


Joined: 13 Feb 2008
Posts: 11
Location: Nigeria
Posted: Sun Feb 24, 2008 9:54 am    Post subject: Accord 2008 Reply with quote
Hi
Thanks for your assistance,did you have dumb for the chip. please advice me what to do.
Regards
Back to top
hcip
Senior Member


Joined: 03 Mar 2006
Posts: 269
Location: Brgy. Commonwealth, Quezon City Philippines
Posted: Sun Feb 24, 2008 10:53 am    Post subject: Re: Accord 2008 Reply with quote
ahmadiga wrote:
Hi
Thanks for your assistance,did you have dumb for the chip. please advice me what to do.
Regards


sorry I have no dump for this car
but you can ask some member here
http://diagcar.exofire.net/phpBB3/

I hope they have

regards
_________________
Back to top
Edmond
Junior member


Joined: 06 May 2006
Posts: 17
Posted: Mon Feb 25, 2008 1:41 am    Post subject: Re: Accord 2008 Solution Reply with quote
hcip wrote:

Hello

If you have interchange the connections of data out pin & data in pin,
This will cause to erase the chip, even you are in reading mode

regards
I don't think so.

To almadiga,
If the #5 & #8 connection are confirm correct. Go to check what you might
have loosen when you tried to probe the continuity to the back of the
board for your connection. Power-up your cluster on the bench. You might
be able to check the 5v+ & 5v- spots where you connect your #5 & #8.
Back to top
samuel
New member


Joined: 02 Feb 2007
Posts: 4
Posted: Sun Jul 27, 2008 6:49 pm    Post subject: 08 accord Reply with quote
just wanted to know did you fugure out 08 honda accord
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Odometer Correction Forum for Digital Mileage Correction -> Mileage Correction Honda All times are GMT
Page 1 of 1

Topic Author Forum Replies Posted
No new posts Transporter T5 2008 Peter Mileage Correction Volkswagen / VW 2 Fri Jan 09, 2009 4:15 pm
No new posts MB A-klass 2008 ,correct with Diga-Co... Tommy Mileage Correction Mercedes-Benz 1 Thu Jan 08, 2009 11:24 pm
No new posts landcrusier 2008 and hilux 2007 adjus... Guest Mileage Correction Toyota 4 Thu Dec 25, 2008 10:58 am
No new posts Polo 2008 Peter Mileage Correction Volkswagen / VW 2 Wed Dec 24, 2008 8:22 pm
No new posts MB sprinter VDO 1999 programing probl... Tommy Mileage Correction Mercedes-Benz 4 Sat Dec 20, 2008 9:40 pm


 
Jump to:  


Protected by Anti-Spam ACP

Diagprog III Kit

Professional version

€ 8.999,00
€ 7.479,00
in stock
+ 19% VAT (BTW)

Version Mercedes-Benz
€ 3.700,00
in stock
+ 19% VAT (BTW)

Version VAG Modelle: VW / Audi / Seat / Skoda
€ 4.100,00
in stock
+ 19% VAT (BTW)

Version BMW & MINI
€ 3.200,00
in stock
+ 19% VAT (BTW)

includes: Hardware, software, all related cables and detailed instructions on a CD with exactly described programming steps as well as high-resolution illustrations as well as a communication programme for the speedometer.
One-week crash course on request in five languages: German, Spanish, English, Greek, Croatian Transportable laptop with integrated instructions and communication programme for the DP3-speedometer system and a professional soldering and hot-air station with fine soldering iron and an integrated hot-air station.

DP3 prices and support