Odometer Correction with the Diagprog 3 programmer

Easy and Safe Mileage Correction


Mileage correction - Help needed please.

Mileage correction - Help needed please. Odometer Correction with the Diagprog III programmer:
Easy and Safe Digital Mileage Correction

Mileage correction - Help needed please.

Goto page 1, 2  Next  
Post new topic   Reply to topic    Odometer Correction Forum for Digital Mileage Correction -> Open Discussion
 
Author Message
ttommo
New member


Joined: 24 Sep 2007
Posts: 5

Posted: Sun Oct 07, 2007 9:13 pm    Post subject: Mileage correction - Help needed please. Reply with quote

Hello all,

I'm trying to adjust the mileage on my Audi TT 2002, I managed to take the dash out & connect the cluster plugs to the dashboard. However, I had difficulty taking the mileage reading because the consult said 'out of range' I think the contact with the red & black wire cables was bad as I held them on the board by hand. Im also wondering in i put the cluster cables the right way up.

I would really appreciate any help & advise on where I'm going wrong and what you would advise I should do to overcome the problem.

I look forward to hearing from you.
Back to top
DashfixDotNet
Moderator


Joined: 20 Nov 2004
Posts: 302
Location: USA

Posted: Mon Oct 08, 2007 4:17 am    Post subject: : Mileage correction - Help needed please. Reply with quote

You have to plug the connectors, apply the red and black wires on to their respecting solder points and only then apply power to your Diga. Go to the TT menu and input the new number, wait until it says "reset" on the screen and jumps back to the main menu. After what disconnect the power of the diga first and the other cables second. Afterwards you have to short to pins of the 908 processor (64 pin device). I think it's pins 5 and 6 counting right to left from the top right corner of the processor.
Note that if at any moment of the programming there's a bad contact of the pins it will result in "km out of range" message. If this is the case install the cluster back in the car and drive it for about 100kms or 65 miles and try again.
If you bought a Diga then you should have a manual and a tech support, even if the unit is a second hand...as long as it's original. If you don't have any it means you bought a cloned unit and you simply are on your own. You pay less but you don't get the most important: tech support.
The help I provided you today is a small sample of what you get if you buy an original Diga from an authorized distributor.

Serge
Back to top
Bannybasher
Senior Member


Joined: 13 May 2008
Posts: 286

Posted: Sat Jun 28, 2008 10:47 am    Post subject: : Mileage correction - Help needed please. Reply with quote

yes serge, that correct. buy direct. saves lots og agro later on.
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Sat Jun 28, 2008 4:32 pm    Post subject: Direct Reply with quote

Hi,

Just a note, it is not possible to buy direct from motosoft anymore, a diga/Dashfixer can only be purchased in the UK via Dashfixer, feel free to call motosoft (orig diga makers) they will inform anyone the same.

In Germany you can purchase from Mr Gleiss at Diga-Soft, he too is an excellent reseller.

With Dashfixer you get free tech support and manuals. 12 hour 7 day helpline, and access to our great forum which is filled with great people using dashfixer everyday.

Regards

Jim
Dashfixer
Back to top
MADAXEMAN
Member


Joined: 22 Jun 2008
Posts: 64

Posted: Sat Jun 28, 2008 6:42 pm    Post subject: : Mileage correction - Help needed please. Reply with quote

An dont forget
If yer buy a seconhand dasfixer, you mus pay £500 to dasfixa, to get de special advise from de scotch experts on de forum,dats on top of the price you pay for de seconhand box.

so member boyz an gurls,if ya buys a seconhan dafixa, den you gottapay
£500 befoor deylet yooonde forum!

yoo can buy a lot of infomation fo £500 elswere.
Back to top
white rabbit
Senior Member


Joined: 16 Jun 2008
Posts: 126

Posted: Sat Jun 28, 2008 9:36 pm    Post subject: : Mileage correction - Help needed please. Reply with quote

It wouldn't take many people from the UK to ring motosoft saying they would not buy from Dashfixer for them to change their mind but I believe it is possible to get hold of a Digapro in the UK. White Rabbit.
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Sun Jun 29, 2008 11:58 am    Post subject: go ahead Reply with quote

yea go ahead, I think you'll get a pleasant surprise, infact I doon't think I know you'll get told to feck off...........good luck you know the number Mr Rabbit
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Sun Jun 29, 2008 12:00 pm    Post subject: digapro Reply with quote

How will you get hold of digapro in the uk? Digapro is a german reseller not the owner! your not doing your homework are you?

Good luck in your quest guys little pathetic.

Sit back while I keep giving my guys great upgrades.

You'll all like the next upgrade............
Back to top
white rabbit
Senior Member


Joined: 16 Jun 2008
Posts: 126

Posted: Sun Jun 29, 2008 11:19 pm    Post subject: : Mileage correction - Help needed please. Reply with quote

How long is that going to be? Two years. White Rabbit
Back to top
MADAXEMAN
Member


Joined: 22 Jun 2008
Posts: 64

Posted: Mon Jun 30, 2008 5:49 am    Post subject: : Mileage correction - Help needed please. Reply with quote

Nex upgrade verie soon, any weak now, send us yer deposits

[need sum spendin monie for de nex usa trip]
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Mon Jun 30, 2008 9:35 am    Post subject: blah Reply with quote

ah more Blah Blah from the 2 ronnies, coupe of boring fuckers and shitbags.
Back to top
secret_squirrel
Member


Joined: 16 Jun 2008
Posts: 37

Posted: Mon Jun 30, 2008 1:38 pm    Post subject: : Mileage correction - Help needed please. Reply with quote

Very funny actually, don't get upset jimjim, you'll only have to join not-drew on his anger management course. Be happy!
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Tue Jul 01, 2008 8:32 am    Post subject: still laughing Reply with quote

Oh I'm very happy, watching you all in here going nowhere gives me great pleasure
Back to top
Clusterslaststand
Senior Member


Joined: 23 May 2008
Posts: 127

Posted: Tue Jul 01, 2008 8:45 pm    Post subject: : Mileage correction - Help needed please. Reply with quote

where are allthe dashfixer2 customers?
do they exist?
Back to top
Dashfixer
Senior Member


Joined: 24 Jan 2005
Posts: 123
Location: Scotland

Posted: Wed Jul 02, 2008 5:27 pm    Post subject: bank Reply with quote

Well I've got the bank balance to proove it, download my records from companies house this year and you'll see.
Back to top
Display posts from previous:   
Post new topic   Reply to topic    Odometer Correction Forum for Digital Mileage Correction -> Open Discussion All times are GMT
Goto page 1, 2  Next
Page 1 of 2

Topic Author Forum Replies Posted
No new posts Flashing Mileage Antony Mileage Correction Fiat 1 Wed Dec 03, 2008 12:35 am
No new posts Tacho mileage calculator!!!! factoring General questions 2 Wed Nov 26, 2008 2:59 pm
No new posts 1991 E31 V12 M/T BMW 850 Where is th... Avechuchoaxel Mileage Correction BMW 11 Thu Nov 20, 2008 11:55 pm
No new posts Digital Mileage Correction Services W... REMAP.ME.UK Odometer Services: Addresses and Contacts 0 Sat Nov 15, 2008 8:34 pm
No new posts Mercedes C300 correction CANAGUAYO Mileage Correction Mercedes-Benz 0 Wed Nov 12, 2008 2:24 pm


 
Jump to:  


Protected by Anti-Spam ACP

Diagprog III Kit

Professional version

€ 8.999,00
7.479,00
in stock
+ 19% VAT (BTW)

Version Mercedes-Benz
3.700,00
in stock
+ 19% VAT (BTW)

Version VAG Modelle: VW / Audi / Seat / Skoda
4.100,00
in stock
+ 19% VAT (BTW)

Version BMW & MINI
3.200,00
in stock
+ 19% VAT (BTW)

includes: Hardware, software, all related cables and detailed instructions on a CD with exactly described programming steps as well as high-resolution illustrations as well as a communication programme for the speedometer.
One-week crash course on request in five languages: German, Spanish, English, Greek, Croatian Transportable laptop with integrated instructions and communication programme for the DP3-speedometer system and a professional soldering and hot-air station with fine soldering iron and an integrated hot-air station.


DP3 prices and support