| |
| Author |
Message |
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Tue Jun 24, 2008 5:52 pm Post subject: Need help on Safrane please |
 |
|
Hello everybody
I've got a problem with a safrane.
I remove the cluster and open it and find the eeprom 93C46.
I try to do it directly with the clip and adapter 93CX6 but nothing.
Then I disolder the eeprom and put it in the clip and try again but no answer.
I put the clip in port 1. And I try in the port 0 and port 2 too but nothing.
I choose the 3 menus: safrane C46V1 safrane C46V2 and safrance mod99
Maybe I forgot something?When I try I get this message :"General failure by reading."
Of course I verify that the Red pin is in 1 (according to what is it written on the eeprom) and on the adapter the red pin is on the left side.
But nothing
If somebody can help me I will be glad.
Thank you a lot |
|
| Back to top |
|
 |
jimdashkirk
Member
Joined: 18 Jun 2008
Posts: 46
Location: bonnie scotland
|
| Posted: Tue Jun 24, 2008 8:35 pm Post subject: : Need help on Safrane please |
|
|
Stick the chip back in to see if the mileage is still there on the lcd
as you may have lost the data.
I cant see why you cant get any data with chip off the pcb.
good luck |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Tue Jun 24, 2008 9:30 pm Post subject: : Need help on Safrane please |
|
|
Thank you for your answer.
I wait about another answers, perhaps I will have another solutions.
But I think you're right maybe I will be oblige to resolder the eeprom and see if I only have the mileage or not. |
|
| Back to top |
|
|
Bannybasher
Senior Member
Joined: 13 May 2008
Posts: 262
|
| Posted: Tue Jun 24, 2008 9:37 pm Post subject: : Need help on Safrane please |
|
|
Sure, i was just making the point , just to see if all data had gone. then you would be wasting your time looking for something that is not there. good luck , hope someone can help.  |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Tue Jun 24, 2008 11:17 pm Post subject: : Need help on Safrane please |
|
|
so the data can gone...? without doing anything?
I just disolder the eeprom and try to read,nothing else.
I thought that normally if there is no data in the eeprom(if they gone....lol)
I will not find this type of error message.
This message just say that there is no connection and the Diga don't find the eeprom...
Tommorow I resolder it and see
Thank you |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Tue Jun 24, 2008 11:17 pm Post subject: : Need help on Safrane please |
|
|
Just one thing....
If data has gone... what can I do? |
|
| Back to top |
|
|
Bannybasher
Senior Member
Joined: 13 May 2008
Posts: 262
|
| Posted: Tue Jun 24, 2008 11:23 pm Post subject: : Need help on Safrane please |
|
|
reload a data set, let me know if you need one , i have 100s of datasets.
no problem, but best to put all back and see.
i had trouble last week with a motorbike, lost all the data becase with arsefixer or clone you have to bridge osc, with dp3 there is no need .
every eeprom is easy to destory. be carfull , and make sure you save data. |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Tue Jun 24, 2008 11:56 pm Post subject: : Need help on Safrane please |
|
|
OK bannybasher, thank you so much.
First thing tommorow I will put it back and see what's happen.
If I need to reload a data I will ask you here (thank you) or if you want you can send it to me here kame_62@hotmail.com
I don't bridge osc when I try with the clip directly, and when I see that there is no connection I dissolder the eeprom to read it.
Perhaps when I try directly and don't bridge osc I destroy it....
Of course first thing to do is to save data
Thank you |
|
| Back to top |
|
|
Clusterslaststand
Senior Member
Joined: 23 May 2008
Posts: 124
|
| Posted: Wed Jun 25, 2008 5:32 am Post subject: : Need help on Safrane please |
|
|
Have you thought of another hobby?
If you delay, waiting for answers to a question that could be solved in 5 minutes!
Try eeprom back on board, all may be ok.
You didnt say what kind of device you use to read eeprom, I suppose its a chinese clone diga.
Ever thought that the equipment may be just shite?
Has it occured to youto try and read another beeprom to see if its your device? |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Wed Jun 25, 2008 8:51 am Post subject: : Need help on Safrane please |
|
|
I never thought of another hobby....and you?
Some people can solve questions in 5 minutes, and others no... that's why they go to ask in a forum...this is normal.
I put back he eeprom and there is nothing, data was deleted.
Could the data be deleted because I remove the eeprom with a rework station and the chip was very hot....
I use Diga like most of people and I said it before....don't suppose it a chinese clone diga!
It read all eeproms normally before this one.
After I will try with another one.
Thank you everybody. |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Wed Jun 25, 2008 8:58 am Post subject: : Need help on Safrane please |
|
|
| Thank you if someone can send to me data... |
|
| Back to top |
|
|
zak
Member
Joined: 16 Apr 2008
Posts: 67
|
| Posted: Wed Jun 25, 2008 12:16 pm Post subject: : Need help on Safrane please |
|
|
V1 + V2 attached.
Attention:
Files are from "Tachodump"
you have to open it also with "tachodump" !
If you open it with any programmer like Ponyprog you will see wrog data ! |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Wed Jun 25, 2008 2:25 pm Post subject: : Need help on Safrane please |
|
|
| Thank you zak I will try and come back here |
|
| Back to top |
|
|
kame
Junior member
Joined: 06 Jun 2008
Posts: 22
|
| Posted: Wed Jun 25, 2008 6:29 pm Post subject: : Need help on Safrane please |
|
|
Hi
Thank you, the second dump work without problem
hello |
|
| Back to top |
|
|
|
|
