| |
| Author |
Message |
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Wed Oct 01, 2008 7:23 pm Post subject: Audi a4 bosch odometer |
 |
|
Some who can help me and explain how to take of the needles and put them back on Audi a4 bosch odometer from yer 2001 and forward
thanks |
|
| Back to top |
|
 |
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Wed Oct 01, 2008 7:46 pm Post subject: Re: Audi a4 bosch odometer |
|
|
| To change mileage on this odomerter, can i do it with obd2 or i gotta go with eeprom? |
|
| Back to top |
|
|
dashradio
New member
Joined: 01 Jan 2008
Posts: 4
Location: Sheffield
|
| Posted: Wed Oct 01, 2008 8:12 pm Post subject: : Audi a4 bosch odometer |
|
|
Twist anti-clockwise & pull at the same time,
before 2001= odb
after quicker to take out & read 24c08 |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Wed Oct 01, 2008 8:36 pm Post subject: : Audi a4 bosch odometer |
|
|
| dashradio wrote: | Twist anti-clockwise & pull at the same time,
before 2001= odb
after quicker to take out & read 24c08 |
There is four needles, two small and two big, is the procedure the same for big and smal? How do i have to do when I am puting them back on the board? |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Wed Oct 01, 2008 8:37 pm Post subject: : Audi a4 bosch odometer |
|
|
| dashradio wrote: | Twist anti-clockwise & pull at the same time,
before 2001= odb
after quicker to take out & read 24c08 |
What do you mean AFTER QUICKER TO TAKE OUT & READ 24c8? |
|
| Back to top |
|
|
almeida
Senior Member
Joined: 07 Aug 2008
Posts: 127
|
| Posted: Wed Oct 01, 2008 8:53 pm Post subject: take needles out |
|
|
hello if you use two spons is better.
two take the needles.
tp put the needles only press. |
|
| Back to top |
|
|
milesbetter
Senior Member
Joined: 01 Aug 2008
Posts: 121
|
| Posted: Wed Oct 01, 2008 9:11 pm Post subject: : Audi a4 bosch odometer |
|
|
| If the car is 2001+ you only need to remove the two large needles if you are going to clip to the eeprom. You can do this cluster from solder points on the back of the board. If you are doing this by removing the needles I don't recommend using two spoons! Tear a slit in a piece of paper, put it under the needle to protect the dial sheet, twist the needle anticlockwise and pull up at the same time. to replace the needle twist anticlockwise and push down at the same time. The needles come off the shafts very easily on this cluster. Use the spoons for stirring your coffee. Arthur. |
|
| Back to top |
|
|
almeida
Senior Member
Joined: 07 Aug 2008
Posts: 127
|
| Posted: Wed Oct 01, 2008 9:19 pm Post subject: take needles out |
|
|
hello,
it´s a good idea to clockwise, we are learning all the time. 
and at my coofe i´m not use sugar.......so i don´t need the spons 
thanks for the idea  |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Wed Oct 01, 2008 9:29 pm Post subject: : Audi a4 bosch odometer |
|
|
| milesbetter wrote: | | If the car is 2001+ you only need to remove the two large needles if you are going to clip to the eeprom. You can do this cluster from solder points on the back of the board. If you are doing this by removing the needles I don't recommend using two spoons! Tear a slit in a piece of paper, put it under the needle to protect the dial sheet, twist the needle anticlockwise and pull up at the same time. to replace the needle twist anticlockwise and push down at the same time. The needles come off the shafts very easily on this cluster. Use the spoons for stirring your coffee. Arthur. |
Thank you for explaining, so to put dem back twist anticlockwise and push down at the same time, do i have to push them down at the same position as i pulled them up?
i am not good at solidering so i dont wanna f... up something! |
|
| Back to top |
|
|
almeida
Senior Member
Joined: 07 Aug 2008
Posts: 127
|
| Posted: Wed Oct 01, 2008 9:41 pm Post subject: put the nedddles |
|
|
you must put the neddels at the same position.
becaufull with this cluster because they have the key imobilazer inside.
if you damage the cluster they car not work more.
try to do more easyer cars if you damage the cluster, you bay a used one,
no problem. |
|
| Back to top |
|
|
yasu
Junior member
Joined: 09 May 2005
Posts: 26
|
| Posted: Thu Oct 02, 2008 10:19 am Post subject: HEX Cood |
|
|
Audi A4 Bosch - 24c08
The mileage is stored in the next lines:
0060: 00 15 00 15 00 15 00 15 00 15 00 15 00 15 00 15
where the next bytes:
00 15 - is a mileage |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Thu Oct 02, 2008 11:29 am Post subject: Re: HEX Cood |
|
|
| yasu wrote: | Audi A4 Bosch - 24c08
The mileage is stored in the next lines:
0060: 00 15 00 15 00 15 00 15 00 15 00 15 00 15 00 15
where the next bytes:
00 15 - is a mileage |
What do you mean, i dont understand, this is all new for me, i am still learning! |
|
| Back to top |
|
|
milesbetter
Senior Member
Joined: 01 Aug 2008
Posts: 121
|
| Posted: Thu Oct 02, 2008 1:38 pm Post subject: : Audi a4 bosch odometer |
|
|
| Take no notice of the previous post. All that is about the mileage locations in the dump. Your tool will do that for you and also if the car is 2001+ it is wrong. Before you start, note down the miles showing and convert this figure to kms. After you have read the eeprom your tool will ask for the current kms. Enter the figure you have and ok it, you will then be asked for the new kms. Enter your new figure (in kms) and ok it. the tool will then program the new figure but only to an accuracy of + or - 1,250 miles. The database uses steps of 4,096 kms about 2,500 miles. Arthur. |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Thu Oct 02, 2008 3:33 pm Post subject: : Audi a4 bosch odometer |
|
|
| milesbetter wrote: | | Take no notice of the previous post. All that is about the mileage locations in the dump. Your tool will do that for you and also if the car is 2001+ it is wrong. Before you start, note down the miles showing and convert this figure to kms. After you have read the eeprom your tool will ask for the current kms. Enter the figure you have and ok it, you will then be asked for the new kms. Enter your new figure (in kms) and ok it. the tool will then program the new figure but only to an accuracy of + or - 1,250 miles. The database uses steps of 4,096 kms about 2,500 miles. Arthur. |
Hello
Thank you for helping, i am from Sweden so my car allready have KM insted of MILES.
Regards Peda |
|
| Back to top |
|
|
Peda
Member
Joined: 29 Sep 2008
Posts: 86
Location: Sweden
|
| Posted: Fri Oct 03, 2008 5:26 am Post subject: : Audi a4 bosch odometer |
|
|
When putting needels back on the board, i read somewhere that, when they are attached on the board to twist them anticlockwise to the point where they suppousted to be at zero mileage and rpm? Is that correct?
Regards |
|
| Back to top |
|
|
|
|
